Shop | ProDrive EV Labs Ltd

5–25 kW Motorcycle Hub-Motor Conversion Project

Plan a scooter or motorcycle conversion around a motor built into the driven wheel.

Cargo-trike electric live axle, compact battery enclosure, controller, charger and small driver display

Project enquiry · Concept illustration

5–25 kW Tricycle E-Axle Conversion Project

Develop a rear differential-axle drivetrain for a passenger or cargo tricycle.

Compact electric transaxle with two capped differential outputs, two CV shafts, battery enclosure and separate cooling and control components

Project enquiry · Concept illustration

15–40 kW Microcar Conversion Project

Plan a compact electric drive around low vehicle mass, packaging and everyday journeys.

Generic compact transverse drivetrain concept with an assembled motor, flush adapter and asymmetric manual transaxle with offset differential

Project enquiry · Concept illustration

40–90 kW Compact Car Conversion Project

Balance daily commuting, family use and compact-car packaging with the requested power.

Compact motor, structural adapter, flywheel hub with pilot support, separate clutch and manual gearbox, battery, cooling and controls

Project enquiry · Concept illustration

80–150 kW Saloon & Passenger Car Conversion Project

Explore everyday, touring or sporting response for saloons, passenger cars and classics.

Compact electric motor assembled to a short manual gearbox through a bellhousing adapter, with battery enclosures, cooling and control components

Project enquiry · Concept illustration

120–250 kW SUV & Pickup Conversion Project

Assess traction, gradients, payload and sustained work for SUVs and pickups.

Passenger-van conversion concept with a central motor connected through a jointed propeller shaft to a conventional rear differential axle

Project enquiry · Concept illustration

100–250 kW Bus & Passenger Van Conversion Project

Develop passenger transport around seating, repeated stops, shift length and depot charging.

Commercial electric driven axle with two wheel hubs, modular battery enclosures, cooling module and control components

Project enquiry · Concept illustration

150–400 kW Goods Truck Conversion Project

Develop the traction brief around vehicle class, working load, gradients and duty cycle.

Electric driven rigid axle with two wheel hubs, battery enclosure, auxiliary hydraulic power unit, cooling and rugged driver display

Project enquiry · Concept illustration

20–150 kW Agricultural & Specialist Conversion Project

Assess low-speed traction, operating hours and auxiliary work as separate demands.

Generic longitudinal conversion concept with motor, adapter, manual gearbox, single rear output and rubber-mounted remote shifter support

Project enquiry · Concept illustration

Custom Vehicle EV Conversion Project

Specify the vehicle class, requested motor power and budget priorities.

Closed residential battery cabinet beside a wall-mounted inverter

Project enquiry · Concept illustration

Residential Battery Storage Package

Residential storage planning around your loads and energy needs.

Industrial energy-storage cabinet with closed service doors

Project enquiry · Concept illustration

Commercial Battery Storage Package

Commercial storage planning for a defined site and duty cycle.

Disconnected battery-management controller and separate cell-monitor board

Project enquiry · Concept illustration

Battery Management System Integration

Battery management integration for your pack architecture.

Empty battery rack enclosure with open gasketed door and mounting rails

Project enquiry · Concept illustration

Battery Rack Enclosure

Battery enclosures selected for the installation environment.

Wall-mounted AC charge point with one cable and capped vehicle connector

Project enquiry · Concept illustration

Home AC Charging Equipment

Home charging matched to the vehicle and electrical supply.

Commercial AC charging pedestal with a closed socket cover

Project enquiry · Concept illustration

Commercial AC Charging Equipment

Commercial AC charging planned around vehicles and site demand.

DC charging cabinet with one heavy cable and covered holstered connector

Project enquiry · Concept illustration

DC Charging Equipment

DC charging planned around vehicles, dwell time and site capacity.

Coiled AC charging cable with two covered connector ends

Project enquiry · Concept illustration

AC Charging Cable

Type 2 cable selection for compatible vehicles and AC charge points.

Portable charging control box with capped supply and vehicle connectors

Project enquiry · Concept illustration

Portable EV Charging Equipment

Portable charging for a compatible vehicle and verified outlet.

Hybrid solar inverter with a closed wiring compartment

Project enquiry · Concept illustration

Hybrid Solar Inverter

Hybrid inverter selection for solar, storage and site loads.

Complete photovoltaic module on a rear display stand

Project enquiry · Concept illustration

Solar Photovoltaic Module

PV module selection for a site-specific solar array.

Finned solar charge controller with a closed terminal cover

Project enquiry · Concept illustration

Solar Charge Controller

MPPT charge control matched to your PV array and battery.

DIN-rail load controller beside three separate current sensors

Project enquiry · Concept illustration

Site Load Management Controller

Load control planned around energy availability and priorities.

Open isolation-equipment case with two-pole tester, proving unit, lockout hardware and gloves

Project enquiry · Concept illustration

High-Voltage Isolation Equipment

Isolation equipment selected for the task and electrical hazards.

Enclosed vehicle control module with two covered connectors

Project enquiry · Concept illustration

Regenerative Control Integration

Regenerative control for compatible motor-drive architectures.

Vehicle diagnostic interface with USB lead and covered vehicle connector

Project enquiry · Concept illustration

Vehicle Diagnostic Interface

Diagnostic interfaces selected for supported target equipment.

Two separate capped orange power cables beside a branched low-voltage loom

Project enquiry · Concept illustration

Custom EV Wiring Harness

Wiring harnesses scoped around your components and routing.

Engineered Conversion Subframe arranged for inspection

Project enquiry · Concept illustration

Engineered Conversion Subframe

Develop a vehicle-specific mounting structure around the selected drivetrain.

Billet Adapter & Coupler Package arranged for inspection

Project enquiry · Concept illustration

Billet Adapter & Coupler Package

Develop the adapter and coupling interfaces for an identified motor and gearbox.

Compact geared bicycle wheel-hub motor with axle and connector interfaces

Project enquiry · Concept illustration

Geared Wheel-Hub Motor

Assess a geared in-wheel drive for a light vehicle or application-specific conversion.

Direct-drive scooter wheel-hub motor with wheel, axle and electrical connection

Project enquiry · Concept illustration

Direct-Drive Wheel-Hub Motor

Explore an in-wheel motor with direct electromagnetic drive of the wheel.

Tricycle axle and reduction assembly with separate motor and controller components for engineering assessment

Project enquiry · Concept illustration

Tricycle Electric Axle

Assess a motor, reduction and differential axle for passenger or cargo tricycles.

One independent electric drive unit with two detached CV shafts for front or rear axle integration assessment

Project enquiry · Concept illustration

Utility & 4×4 Electric Axle Integration

Develop a front or rear e-axle integration brief for a utility vehicle.

Recorded ProDrive EV Labs Ltd native driver display with speed, battery and charging information; sample readings

Project enquiry · Concept illustration

PEV OS Dashboard & HMI Integration

Driver information, battery and charging views, diagnostics and scoped phone functions.

Enclosed vehicle controller concept with keyed low-voltage connectors and mounting ears

Project enquiry · Concept illustration

PEV VCU Integration System

Vehicle-state supervision, CAN integration, diagnostics and guarded calibration.

Freight-van conversion concept with a central motor, connected propeller shaft, supported conventional rear axle, modular battery enclosures and dual-fan cooling

Project enquiry · Concept illustration

100–250 kW Commercial Van Conversion Project

Develop a delivery or service van around payload, stop frequency and the working day.

Illustrative compact automotive body control enclosure with two recessed multipin connector receptacles

Project enquiry · Concept illustration

Assess one central motor driving a conventional axle through a propeller shaft.

Propeller shaft concept with flange-mounted universal joints and a sliding splined section; exposed splines illustrate the mechanism, not an approved installed engagement or seal.

Project enquiry · Concept illustration

Propeller Shaft Assessment

Define the shaft between a longitudinal drive and a conventional rear axle.

Conventional mechanical rear axle concept with one pinion input, differential, axle tubes and wheel-end drum brakes; no motor is integrated.

Project enquiry · Concept illustration